Jungheinrich Etv 216 Error Codes -

Drive pedal activated but no direction switch (forward/reverse) is active. Solution: Check direction switch operation. 1908.1 / 2908.1 (Seat/Belt Switch):

Comprehensive Guide to Jungheinrich ETV 216 Error Codes: Diagnostics and Troubleshooting

For more complex faults, professional diagnostic software is required. Jungheinrich technicians use a proprietary program called . It contains full technical service information, repair instructions, and detailed schematics.

: Drive pedal activated during startup. The truck will not move until the pedal is released and re-pressed.

Indicates no pulses from the steering setpoint device. Usually requires checking the or wire connections. 1901.1: Startup Operator Error jungheinrich etv 216 error codes

| Error Code | Description | Possible Cause | Recommended Action | | :--- | :--- | :--- | :--- | | | Drive system communication failure | A CAN bus error or a wiring fault is preventing communication between drive system components. | Inspect the CAN bus lines for damage. A simple restart of the truck (power cycle) can sometimes resolve this. | | 019 | Disable armature faulty | A fault in the motor's speed sensor, often part of a motor bearing, or a short circuit in the power stage. | Requires a thorough inspection of the motor's speed sensor and controller (often an AS4814Plus). May require component replacement. | | 203 | Drive motor controller fault | The drive controller is overheating or has a hardware error. | First, inspect the controller's cooling system. If the code persists, it may require professional service or replacement. | | 1310 | General drive system fault | A non-specific error preventing movement. Often related to a sensor or accelerator pedal input issue. | Inspect the accelerator pedal sensor and its connections. As one technician noted, sensor issues on the gear ring have been a known culprit on similar models. |

Weak or dying batteries cause voltage drops when pulling high current (e.g., trying to lift a heavy load). This drop confuses the control processors and triggers random error codes. Check the water levels, cell voltages, and cable connections. Step 3: Inspect the Safety Interlocks

Because reach trucks utilize electronic fly-by-wire steering, any fault in this system will immediately disable travel for safety reasons.

Faults related to the drive motor, accelerator pedal, or transmission. Jungheinrich technicians use a proprietary program called

Jungheinrich trucks generally display error codes on the main driver display (can-bus system). These codes usually consist of a multi-digit number, sometimes preceded by a letter or specific icon (like a wrench).

While cleaning a switch or resetting the power can fix minor logic glitches, never attempt to bypass safety sensors or alter controller parameters yourself. You should call a professional if:

Engaging the electromagnetic brake and disabling travel to prevent catastrophic component failure. Most Common Jungheinrich ETV 216 Error Codes

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later. The truck will not move until the pedal

| Error Code | Description | Possible Causes & Suggested Actions | |:---|:---|:---| | | Disable armature faulty; Power stage short circuit. | A serious electrical fault, often triggered by a faulty speed sensor or a short circuit in the AC motor controller. Check the motor encoder and sensor wheel alignment [8†L33-L35]. In some cases, the traction controller itself may be faulty [8†L11-L12]. | | Error 70 | Component fails to respond or responds incorrectly to self-test. | Often indicates a voltage supply problem. Check the power supply behind the main contactor contact, as the voltage may be lower than the rated operating voltage [24†L10-L12]. This error can occur in conjunction with Error 19 [31†L23]. | | Error 115 | Steering contactor or line contactor fault. | Commonly related to a burnt or shorted power stage or contactor failure. Replace the contactor and thoroughly inspect the PCB for burned connections [26†L16-L18]. Both the steering controller and the contactor itself should be examined [25†L13-L14]. |

: Triggered during a self-test when a motor connection wire is broken or the motor itself has failed. System & Operational Messages

The reach truck relies on a diagnostic monitoring system to protect its mechanical components and ensure driver safety. When a component operates outside of normal bounds, the onboard system blocks unsafe operations and triggers a specific event code on the operator display.

Discussion: Jungheinrich ETV 216 Error 047 - Forklift Action

Jungheinrich uses a standardized, CAN-based diagnostic system, so the error codes you see are similar across many models, including the EFG series forklifts and other ETV/ETM reach trucks.

When an error code appears on your ETV 216 display, follow this standard operational sequence before calling a service technician.